| Running With Scissors |
| Hull No. 330-3101 |
| year | |
| 2001 | install 3 gang battery voltmeter |
| 2002 | build new 30 gallon portable livewell |
| 2003 | 50 amp breaker for genset |
| 2003 | added GEN SEP to generator exhaust |
| 2003 | completed repair of removed bonding system (ongoing – piece by piece) |
| 2003 | new gen sep for generator exhaust system Centek #1020150 $184.01 |
| 2003 | Onan 6.5 genset replaced with NextGen 5.0 diesel & new custom built 17 gallon tank NextGen replaced with Northern Lights 2018 |
| 2003 | Raymarine Smartpilot S1G ST600 motor & rudder sensor kept, all else upgraded to Axiom suite 2019 |
| 2003 | replace 115 v recepticle & all weather enclosure for wet bar |
| 2003 | replace factory trim tabs 9×24 With 12×24 and 3″ drop fins Bennet 5515606 |
| 2003 | replace wooden backing plates at swimplatform with Starboard |
| 2003 | replaced cabin referigerator with Sears stainless steel model 204693445 |
| 2004 | autopilot rudder sensor bracket installed with STARBOARD |
| 2004 | rebuilt radar arch damaged during cat 4 hurricane Charley, all wood removed and aluminum tubes glassed in for amazing rigidity |
| 2004 | remove cleats and rebed bases |
| 2004 | Remove bowrail one side at a time and rebed all bases with 4200 and new fasteners |
| 2004 | replaced engine crossover solenoid |
| 2004 | replaced inoperative dual tone horns |
| 2004 | set up first aid kit |
| 2005 | blast bottom and reseal with barrier coat and 2 coats Micron Plus at All Marine Fiberglass Repairs |
| 2005 | New Cruisair 16,000 BTU with reverse heat |
| 2005 | RayMarine Autopilot with Fluxgate Compass installed – updated to Raymarine Axiom suite 2019 |
| 2005 | replaced all bilge hoses |
| 2005 | survey by Bob Gulick prior to 2005 refit to confirm hull condition prior to removal of factory 454 Crusaders |
| 2006 | added fresh water flush to generator |
| 2006 | added fuel shut off valves at tank |
| 2006 | added quick disconnects to all hose bib connections |
| 2006 | added Racor vacuum gauge kits at top of Raycor 900’s (2) |
| 2006 | added spare 1.75″ shaft |
| 2006 | added spare props |
| 2006 | added syphon break on both engine exhaust systems as a prudent measure |
| 2006 | all non-compliant AIRPAX 12v single breakers replaced |
| 2006 | all maleron thru hulls replaced with new bronze thruhulls |
| 2006 | build new aluminum engine 1/2″ beds, throughbolted & bonded with 5200 to stringer tops to accommodate diesel engine torque |
| 2006 | complete rebuild of head & vacuflush system 2006 & 2021 |
| 2006 | covered bottom half of brand new fuel tank with aluminum primer and epoxy paint |
| 2006 | engine battery disconnect switches |
| 2006 | engine oil pumpout kit for Yanmar engines and genset |
| 2006 | engine raw water intakes modified for removing seawater as a bilge pump |
| 2006 | Fireboy MA2-200 Automatic Sensor Fire Extinguisher kit with engine shutdown and 12′ manual pull cable |
| 2006 | fresh water flushing fittings installed |
| 2006 | fuel lines replaced to engines, tank & raycors |
| 2006 | fuel tank replaced with new 242 gal tank |
| 2006 | head seat replaced 2006 & 2021 |
| 2006 | ignition key switches modified into main 12v panel with individual breakers |
| 2006 | install additional engine room explosion proof lights |
| 2006 | installed additional Layered SoundDown insulation in engine room |
| 2006 | installed Dripless shaft logs PYI |
| 2006 | installed electrically adjustable “Patrick” radar pedestal |
| 2006 | installed engine room lighting |
| 2006 | installed Racor 500 for genset |
| 2006 | installed twin Racor 900 Fuel filter system for Yanmars |
| 2006 | new engine sea strainers Groco 2″ |
| 2006 | new engine seacocks 2″ |
| 2006 | new HVAC by Blue Water Marine 16,000 BTU AC & heat |
| 2006 | propeller shafts & 1 spare 1 3/4″ A-19 |
| 2006 | pushbutton dash starter switches added |
| 2006 | rebuilt instrument panel, replaced all guages, tachometers and BlueSeas switches |
| 2006 | replace Hynautic helm with SeaStar helm & ram |
| 2006 | replace radar mount all around light with powdercoated cutom “Patrick” unit |
| 2006 | replaced all hoses |
| 2006 | replaced bilge blower |
| 2006 | replaced engine emergency buzzers |
| 2006 | replaced fuel tank |
| 2006 | replaced stern light with LED |
| 2006 | replaced twin lever shift & throttle controls & new shift cbles |
| 2006 | replaced Yanmar timing belts & tensioners – both engines |
| 2006 | SPARE FAN BELTS, FUEL FILTERS kept on board in a dry box |
| 2006 | steering helm and ram replaced with Teleflex unit |
| 2006 | VDO fuel level guage |
| 2006 | VDO oil pressure guages |
| 2006 | VDO Tachometers magnetic pickup tach |
| 2006 | VDO voltmeters |
| 2006 | VDO water temp guages |
| 2006 | water heater tank – Raritan with engine heater lines |
| 2006 | Yanmar 6LP engines serial # 56001 PORT & 56008 STBD |
| 2007 | “soft” rope caulk seal added to powercenter for easy access |
| 2007 | added fresh CO and smoke detectors at salon & fwd berth |
| 2007 | added mirrors in salon & fwd berth |
| 2007 | added spring hinge stays to doors at lazerette, cockpit wet bar, medicine cabinet and fwd berth closet |
| 2007 | aft deck removed and recored at wet bench seat attachment points |
| 2007 | diesel electric fuel pump added in lazerette to prime fuel filters & transfer fuel from tank to tank |
| 2007 | installed boost guages |
| 2007 | installed new VHF with DSC & NEMA 0183 output to floscan |
| 2007 | installed pyrometers |
| 2007 | installed VHFexternal speaker |
| 2007 | replace radar arch spreader lights with LED’s |
| 2007 | replaced freshwater dockside inlet valve |
| 2007 | replaced clear ice-maker hose with sunlight filtering hose to eliminate algae possibility |
| 2007 | replaced trim tab bottom brackets & pins |
| 2007 | stainless steel drink holders added in cockpit |
| 2008 | breaker 12v main replaced and spare onboard |
| 2008 | install engine room light indicator lamp (should be two) |
| 2008 | removed carpet and installed Plasteak flooring in cabin , head & stairway |
| 2008 | replace bilge pump breaker set |
| 2008 | sound insulated lasarette hatch with SOUNDOWN |
| 2009 | install new water filter |
| 2009 | livewell pump upgraded to 1100 GPH & 1.25″ hose |
| 2009 | replaced 30 amp – 120 volt shore power breakers Square D part #QOU230 spares on board |
| 2009 | replaced factory cockpit floor lights with red LED fixtures (3) |
| 2009 | stainless hold downs for 30 gallon livewell setup |
| 2010 | replaced all cabin speakers |
| 2010 | boat surveyed at 2001 purchase, 2006 refit and for 2010 re-insurance |
| 2010 | canvas: boots needed for aft&fwd bimini & drop curtain, transom cover, |
| 2010 | ground windshield frame to bonding system for safety |
| 2010 | hot water heater – replaced leaking blow off valve |
| 2010 | install bilge alarms tied to the horn in all three bilges |
| 2010 | measure depth and height to waterline with and w/o antenna and post both on dash |
| 2010 | paint exhaust outlets with special black paint sand throughly first |
| 2010 | recoat bottompaint |
| 2010 | replace all around light & housing with new LED |
| 2010 | replace nav lights and housings with new LED lights |
| 2010 | replaced door rollers on head and fwd electric cabin doors |
| 2010 | set deadbolt pin into galley table for solid UP position |
| 2010 | survey by Bob Gulick to re-insure expired policy with BoatUS Insurance |
| 2011 | installed breathing vents in salon storage compartments for fwd cabin, port & stbd setees. No trapped air, ever. |
| 2011 | Yanmar engines 250 hour valve adjustment completed by Bill Nelson |
| 2012 | added reading lamps in fwd cabin with dimmers, night light and USB charging stations |
| 2013 | new flatscreen TV |
| 2013 | replaced both fuel tank sending units with quality WEMA float style units |
| 2013 | replaced GFCI outlets in galley & all std cabin outlets with child deterrents |
| 2014 | Floscan system & digital Floscan tachometers |
| 2014 | add spray foam insulation to ceiling bulkhead areas beside flourescent lights in salon |
| 2014 | add threads to stbd engine pyrometer probe |
| 2014 | added hidden, separate red and blue cockpit under gunnel rope lights |
| 2014 | change aft white light to LED |
| 2014 | install bilge counter on fwd standard bilge |
| 2014 | install emergency bilge pump in fwd bilge |
| 2014 | install red LED lights at cabin stairway |
| 2014 | install red lights in head, cabin & galley |
| 2014 | install white LED lights in head, cabin & galley |
| 2014 | insulate area above and behind galley storage cabinet (top) |
| 2014 | insulate area behind & beside head medicine cabinet |
| 2014 | new U-Line icemaker/fridge in cockpit |
| 2014 | removed factory flouresent lighting and replaced with LED’S |
| 2014 | REMOVED HANDLE at blackwater discharge and added keyed lockout switch in head to comply with Key West requirements |
| 2014 | removed tachs at 397 hours and replaced with Floscan system |
| 2014 | replace cockpit white lights with red LED lights |
| 2014 | replace Gaffrig pyrometers and lead wires with Hewitt |
| 2014 | replace pinstriping top of deck |
| 2014 | replace shower bilge pump hose, installed backflow ball valve and added anti-syphon loop |
| 2014 | re-striped all horizontal and radar arch striping |
| 2014 | re-wire existing center emergency bilge and fwd bilge pumps to helm console switches, both wired to center generator battery |
| 2015 | replace fwd/aft wood supports under rear cockpit outboard sides, below step with aluminum tube |
| 2015 | replace microwave |
| 2015 | replaced undergunnel wood with PVC board |
| 2016 | replaced digital clock at dash |
| 2016 | Yanmar – Walker air filter systems added |
| 2017 | replaced all lighting with LEDs Added additional updated fixtures and red interior lights for night use |
| 2017 | replaced rollers on sliding door to cabin |
| 2018 | all cabin fabrics and cushions replaced with commercial MOVIE THEATRE quality fabrics |
| 2018 | all new grey canvas |
| 2018 | 12 v recepticles and USB charging ports added to helm, salon & fwd berth |
| 2018 | added freshwater filter screen and clear canister particulate filter |
| 2018 | added high density charcoal canister filter at galley sink |
| 2018 | all formica surfaces in cabin and cockpit updated |
| 2018 | all new grey canvas covers to protect all teak, bow pulpit, vinyl surfaces and west facing transom |
| 2018 | install 5 Seateck underwater lights, with zero holes in the transom |
| 2018 | NEW Northern Lights 673L with optional extra low vibration mounts and flexible sound shield |
| 2018 | new rudder bushings installed, port rudder base strengthened with fiberglass and Starboard |
| 2018 | replace all wooden deck hatches with fiberglass |
| 2018 | replace entire stainless steel rub rail band |
| 2018 | replace swim platform with new Plasteak in identical replacement with 2 additional factory braces |
| 2018 | replace Xantrex with 3 bank BLUE SEAS charger with remote panel |
| 2018 | replaced all deck furniture bottoms with PVC board |
| 2018 | replaced bellows and running surface on PYI dripless shaft logs |
| 2018 | replaced both cabin hatches with BOMAR including spring loaded, retractible shades & bug screens |
| 2018 | replaced freshwater pump with high capacity model, purchased additional pump as an onboard spare |
| 2018 | replaced red bulb behind powercenter doors with red LED strip light |
| 2018 | replaced stainless steel galley sink |
| 2018 | updated galley faucet with newest style |
| 2018 | upgraded fresh water system accumulator to small household style |
| 2019 | removed dual princess stovetop, replace with new Kenyon below counter single burner stove |
| 2019 | exhaust /water temp alarm system for Yanmars & generator |
| 2019 | Raymarine Axiom suite added with dual downvision and Realvision transducers |
| 2019 | removed factory curtains and updated with custom opaque pull down spring loaded blinds |
| 2019 | replace latch pulls on engine room lazarette and all cabin hatches |
| 2019 | replaced shower head and new shut-off washers |
| 2019 | Yanmar – add temp alarms with clamp on sensors to wet exhaust system |
| 2020 | add new magnetic float switch to blackwater tank |
| 2020 | add running light and manual override switch to vaccuflush |
| 2020 | adde red and white LED lighgts to FWD berth |
| 2020 | replace front window weatherstripping |
| 2020 | replace shore power connnections & wiring to main panel |
| 2020 | replaced Yanmar eexhaust elbows with stainless steel elbows |
| 2020 | upgrade/replace livewell/washdown pump |
| 2020 | Upgraded to FUSION stereo system with JL speakers, Subwoofer and amplifier |
| 2021 | install new duckbill valves on vacuflush 2005, 2015, 2021 |
| 2021 | install waste tank monitor upgraded to magentic sensor WEMA float style unit |
| 2021 | installed LED lights in both closets |
| 2021 | re-bed bowrail & all deck hardware used 4200 in 2002 used butyl tape in 2021 |
| 2021 | rebuild vaccuflush complete, 2005, 2021 |
| 2021 | replace fixed wooden post for steering ram with custom made Starboard unit |
| 2021 | replaced props with custom VEEM propellers |
| 2021 | upgraded VHF antenna to top quality unit |
| note | new, spare vacuflush pump is kept onboard |
| note | note: latches behind insturment pod are Southco 1/2 turn latches |
| note | obtained spare raw water pumps (1)for genset and (2) for Yanmars |
| NOTE | windshield wipers are now NAPA #60-1840 replacing std units with 18″ blades |
| NOTE | Xantrax three bank battery charger with diode panel voltage readout |
| NOTE: | wire duct covers Taylor #99040, Grainger #3LR77 for open slot wiring duct # 3LR72 |
